Round Analog Gauge
Round Analog Gauge
Round Analog Gauge
Please check on OSX + feedback welcomed
Source: http://www.ctvrtky.info/wp-content/uplo ... dGauge.zip
Lukas
Please check on OSX + feedback welcomed
Source: http://www.ctvrtky.info/wp-content/uplo ... dGauge.zip
Lukas
Re: Round Analog Gauge
@ l1marik,
Very nice, thank you.
Looks good and appears to work fine on my MacBook.
Very nice, thank you.
Looks good and appears to work fine on my MacBook.
DE AA EB
- VB6_to_PBx
- Enthusiast
- Posts: 625
- Joined: Mon May 09, 2011 9:36 am
Re: Round Analog Gauge
Lukas ( l1marik ),
thanks a bunch for all the
Weather meters / gauges you've created !!!
if you are looking for more ideas
on creating Dials , Gauges , or Meters ??
what about these :
Speedometer
RPM
Oil pressure
Fuel pressure
Vacuum
Oil temperature
Water temperature
O2 Sensor ( Oxygen Sensor )
EGT ( Exhaust Gas Temperature )
Digital Numbers ( LED )
thanks a bunch for all the
Weather meters / gauges you've created !!!
if you are looking for more ideas
on creating Dials , Gauges , or Meters ??
what about these :
Speedometer
RPM
Oil pressure
Fuel pressure
Vacuum
Oil temperature
Water temperature
O2 Sensor ( Oxygen Sensor )
EGT ( Exhaust Gas Temperature )
Digital Numbers ( LED )
PureBasic .... making tiny electrons do what you want !
"With every mistake we must surely be learning" - George Harrison
Re: Round Analog Gauge
Dear VB6_to_PBx,
It is not problem, question is only a design of it. Can you propose any?
Picture will enough.
Lukas
It is not problem, question is only a design of it. Can you propose any?
Picture will enough.
Lukas
- VB6_to_PBx
- Enthusiast
- Posts: 625
- Joined: Mon May 09, 2011 9:36 am
Re: Round Analog Gauge
hi Lukas , sorry for this late Reply ,l1marik wrote:Dear VB6_to_PBx,
It is not problem, question is only a design of it. Can you propose any?
Picture will enough.
Lukas
here's a Picture :
PureBasic .... making tiny electrons do what you want !
"With every mistake we must surely be learning" - George Harrison
- Kwai chang caine
- Always Here
- Posts: 5353
- Joined: Sun Nov 05, 2006 11:42 pm
- Location: Lyon - France
Re: Round Analog Gauge
Works well here, very nice
Thanks for sharing
Thanks for sharing
The happiness is a road...
Not a destination
Not a destination
Re: Round Analog Gauge
There's so much
Try a 3D Pi Chart for example, many have failed to do so
Try a 3D Pi Chart for example, many have failed to do so
地球上の平和
- VB6_to_PBx
- Enthusiast
- Posts: 625
- Joined: Mon May 09, 2011 9:36 am
Re: Round Analog Gauge
thank Saki for your Pic ,
i was about to post a few similar pics ,
but your 1 pic captured most of what multiple pics i was going to post .
on my Engine Dyno , i can change custom GUI Gauges looks + sizes
much better than the crummy generic Pic i posted above ,
i just haven't had time to go and create new Gauges ,
will do later .
i was about to post a few similar pics ,
but your 1 pic captured most of what multiple pics i was going to post .
on my Engine Dyno , i can change custom GUI Gauges looks + sizes
much better than the crummy generic Pic i posted above ,
i just haven't had time to go and create new Gauges ,
will do later .
PureBasic .... making tiny electrons do what you want !
"With every mistake we must surely be learning" - George Harrison
Re: Round Analog Gauge
Create a CanvasGadget in your favorite FormDesigner and use an IncludeFile that contains the "Gauge_Analog_Round() procedure?
- It was too lonely at the top.
System : PB 6.10 LTS (x64) and Win Pro 11 (x64)
Hardware: AMD Ryzen 9 5900X w/64 gigs Ram, AMD RX 6950 XT Graphics w/16gigs Mem
System : PB 6.10 LTS (x64) and Win Pro 11 (x64)
Hardware: AMD Ryzen 9 5900X w/64 gigs Ram, AMD RX 6950 XT Graphics w/16gigs Mem
Re: Round Analog Gauge
I'm just a beginner.
Please, guide me through it.
Please, guide me through it.
Code: Select all
Global Window_0
Global Gaget1
Declare Gaget1_Events(EventType)
Procedure OpenWindow_0(x = 0, y = 0, width = 480, height = 320)
Window_0 = OpenWindow(#PB_Any, x, y, width, height, "", #PB_Window_SystemMenu)
Gaget1 = CanvasGadget(#PB_Any, 16, 16, 152, 152)
EndProcedure
Procedure Window_0_Events(event)
Select event
Case #PB_Event_CloseWindow
ProcedureReturn #False
Case #PB_Event_Menu
Select EventMenu()
EndSelect
Case #PB_Event_Gadget
Select EventGadget()
Case Gaget1
Gaget1_Events(EventType())
EndSelect
EndSelect
ProcedureReturn #True
EndProcedure