With pb 5.20, whenever I open or close a project, the IDE is not responsive for about 15 seconds.
Windows 8 X64 with PB 5.20 32 bits on a Core I7 2.4ghz
5.20 Freeze when a project is opened/closed
-
- Always Here
- Posts: 6425
- Joined: Fri Oct 23, 2009 2:33 am
- Location: Wales, UK
- Contact:
Re: 5.20 Freeze when a project is opened/closed
That very much sounds like your Anti-Virus taking a look.....
IdeasVacuum
If it sounds simple, you have not grasped the complexity.
If it sounds simple, you have not grasped the complexity.
Re: 5.20 Freeze when a project is opened/closed
I don't have any :/
Re: 5.20 Freeze when a project is opened/closed
Poshu,Poshu wrote:With pb 5.20, whenever I open or close a project, the IDE is not responsive for about 15 seconds.
Windows 8 X64 with PB 5.20 32 bits on a Core I7 2.4ghz
I notice that you are using Win 8
- Go to the control panel
- Start 'Windows Defender'
- Press the Settings Tab
- Highlight the 'Excluded files and locations'
- browse for (and add) the temporary location that PureBasic uses
e.g. mine is: C:\Users\Bob\AppData\Local\Temp
Note the advice at the top of the screen... but I've never had problems
HTH,
--Bob
- It was too lonely at the top.
System : PB 6.10 Beta 9 (x64) and Win Pro 11 (x64)
Hardware: AMD Ryzen 9 5900X w/64 gigs Ram, AMD RX 6950 XT Graphics w/16gigs Mem
System : PB 6.10 Beta 9 (x64) and Win Pro 11 (x64)
Hardware: AMD Ryzen 9 5900X w/64 gigs Ram, AMD RX 6950 XT Graphics w/16gigs Mem
-
- Always Here
- Posts: 6425
- Joined: Fri Oct 23, 2009 2:33 am
- Location: Wales, UK
- Contact:
Re: 5.20 Freeze when a project is opened/closed
That very much sounds like your Anti-Virus taking a look
I don't have any
Start 'Windows Defender'
IdeasVacuum
If it sounds simple, you have not grasped the complexity.
If it sounds simple, you have not grasped the complexity.
Re: 5.20 Freeze when a project is opened/closed
windows defender service was one of the first things I turned off :/
I mostly use my comp with ubuntu and I only start win 8 to compile stuff, so these 15 seconds are not a very big deal anyway.
I mostly use my comp with ubuntu and I only start win 8 to compile stuff, so these 15 seconds are not a very big deal anyway.
- Crusiatus Black
- Enthusiast
- Posts: 389
- Joined: Mon May 12, 2008 1:25 pm
- Location: The Netherlands
- Contact:
Re: 5.20 Freeze when a project is opened/closed
I had the same issue once, yesterday. I'm not sure what caused this, as NOD32 does
not interfere with PureBasic (I even disable it while I'm programming).
In my case, PB was hanging for more than 15 seconds on Windows 7 Home Premium x64.
While this was happening, I checked task manager to see how much memory and cpu was
being used by PureBasic, but nothing out of the ordinary there. CPU at 0% and memory
didn't increase.
not interfere with PureBasic (I even disable it while I'm programming).
In my case, PB was hanging for more than 15 seconds on Windows 7 Home Premium x64.
While this was happening, I checked task manager to see how much memory and cpu was
being used by PureBasic, but nothing out of the ordinary there. CPU at 0% and memory
didn't increase.
Re: 5.20 Freeze when a project is opened/closed
I am using Windows 8.1 and PureBasic 5.21 LTS
For quite some time I install programs no longer into ''C:\Program Files' or 'C:\Programme' ) or 'C:\Program Files (x86)' or 'C:\Programme (x86)'.
I always split my hard drive, and then I install programs, where I expect that they often access the Program Directory -
into e.g. 'D:\ProgramFiles(x86)\PureBasic' without any blanks,
so I have then no access problems under Windos 7 and above, and the handover of the program path as a parameter (just without blanks) saves me the one or the other worse.
So I did not have any problems yet with my PureBasic 5.21 LTS
For quite some time I install programs no longer into ''C:\Program Files' or 'C:\Programme' ) or 'C:\Program Files (x86)' or 'C:\Programme (x86)'.
I always split my hard drive, and then I install programs, where I expect that they often access the Program Directory -
into e.g. 'D:\ProgramFiles(x86)\PureBasic' without any blanks,
so I have then no access problems under Windos 7 and above, and the handover of the program path as a parameter (just without blanks) saves me the one or the other worse.
So I did not have any problems yet with my PureBasic 5.21 LTS
I may not know much, but I try a lot
-
- Addict
- Posts: 4519
- Joined: Thu Jun 07, 2007 3:25 pm
- Location: Berlin, Germany
Re: 5.20 Freeze when a project is opened/closed
So what?EfDschoma wrote:I am using Windows 8.1 and PureBasic 5.21 LTS
For quite some time I install programs no longer into ''C:\Program Files' or 'C:\Programme' ) or 'C:\Program Files (x86)' or 'C:\Programme (x86)'.
I always split my hard drive, and then I install programs, where I expect that they often access the Program Directory -
into e.g. 'D:\ProgramFiles(x86)\PureBasic' without any blanks,
so I have then no access problems under Windos 7 and above, and the handover of the program path as a parameter (just without blanks) saves me the one or the other worse.
So I did not have any problems yet with my PureBasic 5.21 LTS
I installed PB 5.21 LTS in the directory C:\Program Files\PureBasic\ (on Windows 7 x64), and did never encounter any problems.